Phosphate adsorption on dried alum sludge: Modeling and application to treatment of dairy effluents.

This study evaluates Alum sludge from drinking water treatment plants for the efficient and cost-effective removal of phosphates from aqueous solutions. Extensive characterization and batch experiments have established that optimal phosphate removal was achieved with a sludge dosage of 20 g L-1 (at an initial phosphate concentration of 100 mg L-1), a pH of 5, a temperature of 23 °C, and a stirring speed of 200 rpm. These conditions significantly reduced phosphate levels, ensuring compliance with legal discharge limits. The Langmuir isotherm, pseudo-second-order kinetic and intraparticle diffusion models best described the adsorption process, highlighting the spontaneous and endothermic nature of the phenomenon. The sludge effectively reduced phosphate concentrations to acceptable levels when applied to dairy effluents. This study underscores the potential of Alum sludge as a viable solution for phosphate management in environmental cleanup efforts.

Study of the catalytic wet air oxidation of p-hydroxybenzoic acid on a fresh ruthenium catalyst supported by different oxides.

The catalytic wet air oxidation (CWAO) of p-hydroxybenzoic acid (p-HBA) was conducted in a batch reactor at 140 °C, and at a total air pressure of 50 bar over Ru-based catalysts. Four materials were selected as supports - TiO2, CeO2-TiO2, ZrO2-TiO2, and La2O3-TiO2 - all of which had mesopores in their texture and pollutant adsorption capacities. The supports were prepared by the sol-gel method, and then impregnated with 3 wt% of Ru precursor. Such characterization techniques as N2-sorption, XRD, XPS, H2-TPR, NH3-TPD, TEM, and HAADF-STEM were used to analyze the different solids. The correlation between catalytic activities and physicochemical properties was discussed. A significant specific surface area (SBET), a large amount of surface-active oxygen, and Lewis acidity sites were observed on cerium-containing catalysts (Ru/CeTi). Fresh Ru catalysts containing cerium showed higher activity than Ru/TiO2, Ru/ZrTi, and Ru/LaTi catalysts. It is assumed that the acidic sites and surface oxygen trap the p-HBA molecule, thus increasing the catalytic properties of the Ru particles which interact with the surface oxygen through the cerium redox process (Ce3+/Ce4+). As the presence of cerium increases surface-active oxygen, it inhibits the deposition of carbon on the surface of the Ru catalyst. The pseudo-second order (PSO) model adequately described the kinetic data of the p-HBA oxidation reaction using Ru catalysts.

Production of biochar from Melia azedarach seeds for the crystal violet dye removal from water: combining of hydrothermal carbonization and pyrolysis.

Biochar has shown large potential in water treatment because of its low cost, good textural properties, and high reusability. In this study, two porous biochars were developed from the Melia azedarach seeds via direct pyrolysis process (B-700) and through hydrothermal carbonization followed with pyrolysis (HB-700). They were characterized by morphology, structural characteristics, and surface features and used to adsorb the crystal violet (CV) dye in water environment. Results of the isotherm approaches demonstrated that the removal capacity of these biochars reached 119.4 mg/g for B-700, and 209 mg/g for HB-700 (at 45°C). Also, the Avrami model best fitted the kinetic data. The electrostatic attraction was regarded as one of the adsorptions mechanisms of CV dye. The regeneration tests reveal that both B-700 and HB-700 are good reusable adsorbents. Finally, findings of the study showed that the hydrothermal carbonization method that precede the pyrolysis process can improve significantly the adsorption capacity of the produced biochar.

Alginate/geopolymer hybrid beads as an innovative adsorbent applied to the removal of 5-fluorouracil from contaminated environmental water.

Water contaminated by cytostatic drugs has many negative impacts on the ecosystems. In this work, cross-linked adsorbent beads based on alginate and a geopolymer (prepared from an illito-kaolinitic clay) were developed for a promising decontamination of the 5-fluorouracil (5-FU) cytostatic drug from water samples. The characterization of the prepared geopolymer and its hybrid derivative was performed by scanning electron microscopy, X-ray diffraction, Fourier transform infrared and termogravimetric analysis. Batch adsorption experiments indicated that alginate/geopolymer hybrid beads (AGHB) allow an excellent 5-FU removal efficiency of up to 80% for a dosage adsorbent/water of 0.002 g/mL and a concentration of 5-FU of 2.5 mg/L. The adsorption isotherms data follow well the Langmuir model. The kinetics data favor the pseudo-second-order model. The maximum adsorption capacity (qmax) was 6.2 mg/g. The optimal adsorption pH was 4. Besides pore filling sorption process, the carboxyl and hydroxyl groups from alginate immobilized onto the geopolymer matrix favored the retention of 5-FU ions by hydrogen bonds. Common competitors, such as dissolved organic matter, do not significantly affected the adsorption. In addition, this material has not only eco-friendly and cost-effective advantages but also excellent efficiency when applied to real environmental samples such as wastewater and surface water. This fact suggests that it could have a great application in the purification of contaminated water.

Easy separable, floatable, and recyclable magnetic-biochar/alginate bead as super-adsorbent for adsorbing copper ions in water media.

This work aimed to develop innovative material by combining properties of magnetic-biochar (derived from peanut shells) and hydrogel bead (MBA-bead) and apply it for adsorbing Cu2+ in water. MBA-bead was synthesized by physical cross-linking methods. Results indicated that MBA-bead contained ∼90% water. The diameter of each spherical MBA-bead was approximately 3 mm (wet form) and 2 mm in (dried form). Its specific surface area (262.4 m2/g) and total pore volume (0.751 cm3/g) were obtained from nitrogen adsorption at 77 K. X-ray diffraction data confirmed Fe3O4 presented in magnetic-biochar and MBA-bead. Its Langmuir maximum adsorption capacity for Cu2+ was 234.1 mg/g (30 °C and pHeq 5.0). The change in standard enthalpy (ΔH°) of the adsorption was 44.30 kJ/mol (dominant physical adsorption). Primary adsorption mechanisms were complexation, ion exchange, and Van der Waals force. Laden MBA-bead can be reused several cycles after desorbing with NaOH or HCl. The cost was estimated for producing PS-biochar (0.091 US$/kg), magnetic-biochar (0.303-0.892 US$/kg), and MBA-bead (1.369-3.865 US$/kg). MBA-bead can serve as an excellent adsorbent for removing Cu2+ ions from water.